Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

The purpose with this study is to compare different systems of grain storage from a financial point of view. Grain that is supposed to be fed to laying hens. The systems that were compared were different airtight storage of grain and a system of conventional storage. To make this case study I choose to compare four different systems. In the case study there was one system with bin drying of the grain, two systems with airtight storage of the grain and one system where you buy dried grain during the season. I made several of capital investment appraisal where I found the cost of each system, then I took the cost and divided it with the total grain use and calculated the cost for each kilogram of grain, and also the cost of the feed. Then I compared the cost from my case study with the cost of buying feed. All the systems except for one, gave a lower cost for the hen feed than buying feed from a dealer The best system, witch were bin drying lower the cost with about 80 000:- SEK.

The aim with the thesis is to get deeper knowledge in one of the subjects botany, livestock technology or economy. I have chosen to get deeper knowledge in how to store potatoes. How are you going to act to keep the quality on the potato during the storage, with a minimum of weight lost? My aim with this thesis is to get a view over how the potato act in storage space. The storage environment is very important in the storage space.

Most of the saw and pulp industries have stored wood nearby their production, the main reason is to have a continuous wood flow to the production. Wet storage of wood is of great importance to keep the wood quality. Without water sprinkling the risk of drying outand decomposition through biological activity increases significantly and will result in a negative effect on future production and quality. One drawback of wet storage of wood is the leaching of chemical substances into the surrounding recipient. The log yard run-off contains phosphorus, nitrogen, phenols and organic substances. These substances can cause problems for the surrounding environment. The main objective of this project is to gain an understanding of the wet storage used by the Swedish wood industry and estimate the environmental consequences that run-off water will have on the recipient.

Latent heat storage is a way to store thermal energy when a phase change material undergoes a phase change. The advantage of latent heat storage is the capability to store more energy per mass unit than other heat storage methods. The most commonly used phase change in latent heat storage is the transition between solid and liquid. Phase change materials can be divided into organics, inorganics and eutectics.In the Nordic electricity market the price of electricity is set every hour by Nordpool spot, which leads to price fluctuations because of changes in demand. The main goal of this report is to create a latent heat storage system in a single-family home and investigate the possibility to save money by charging the latent heat storage system when the price of electricity is low, and discharge when the price is high.The thermodynamic model consisted of a ?tube-in-tube? heat exchanger with phase change material in the outer tube and water as the heat transfer fluid in the inner tube.

Texo Application has created robots that they call for satellites; with these you can feed in storage pallets into a satellite storage. Satellite storages consist of channels in height (e.g.3 to 8 pieces) and width (e.g.3 to 100 pieces). Channels can be different long (e.g. 5 to 200 pallets). At deposit of a storage pallet the truck insert the satellite in a channel and then the pallet, the pallet is driven into the channel until it reaches another pallet or the other end.

A vehicle that carries a person sitting in a wheelchair has been rebuilt. The original vehicle was provided with a petrol engine, hydrostatic drive and a mechanical steering rod, making it noisy and hard to maneuver. The purpose with this project was to convert the vehicle to make it more environmental and easier to drive.A new design has been proposed where an electrical drive has replaced the noisy combustion engine and an electrical motor with joystick control has replaced the manual steering.The project was divided into two parts. One mechanical part where the construction of the drive and steering were to be decided. The other part involved programming the microprocessor and implementation of all the necessary electrical for the control system of the vehicle.

In today?s society there is an increasing demand for renewable energy sources such as sun and wind power. These sources are intermittent, and energy storage is therefore needed to ensure a constant power supply. This report compares pumped hydro energy storage (PHES), compressed air energy storage (CAES), flywheels, batteries, super magnetic energy storage (SMES) and hydrogen energy storage.The opportunities for further development are limited for PHES and CAES in comparison with the other technologies. Lithium-ion batteries and hydrogen energy storage are considered to have the most potential in the future.

Denna examensrapport redogör för hur man kan få en kortslutningsskyddadoch säker inkoppling av en DC-länk mellan två skiljda elektriska system.Rapporten bygger på hur en lastbil ska kunna få en större säkerhet för attbibehålla sina elektriska bromsar om tex ett av bromssystemen tappar sinordinarie matning.Lastbilens bromssystem består idag av två skiljda elektriska system med ett 24volts strömförsörjande batteri vardera. Det ingår två stycken elektriskabromsar i varje system. Om det tex blir fel på en av bromsarna och dennapåverkar ett av systemen vill man kunna koppla bort denna enskilda bromsmed sitt system. Man vill även kunna försörja den fungerande bromsen somsitter i samma system via en så kallad Axle Link. Denna strömmatningslänksitter mellan två hjulpar på samma axel.I denna studie undersöktes möjligheten att realisera en kortslutningsskyddadoch säker DC-överföring via en Axle Link, i första hand med diskretakomponenter.

This work covers a broad analysis of the risks that could impact the achievement of electrical safety of electrical installations. The work includes both electrical equipment such as the installation of electrical equipment.The report illustrates the main technical characteristics of electrical connections greater than 10 mm2 and provides an introduction to the crimping systems for copper and aluminum conductors. In addition to that analyzes the factors that are important to assure the quality of an electrical connection throughout the value stream in terms of both materials such informations. Furthermore analyzed deeper the need for skills development of technicians and other staff.The different parts of this work are analyzed and presented, in theory to studies carried out both at Elpress AB and partly with the help of other scientific reports dealing with similar subjects. In addition, presents a survey that will help understanding the current perception of the electrical connections and cable crimping systems among end users.

Active work to increase the efficiency of energy use is taking place in Sweden and throughout all of Europe. Electricity is an important part in our society?s energy system which means that the electrical grid operators and associated therewith has a central role in this work. Monitoring and controlling the electrical grids are managed from the distribution system operator?s DC, dispatch center.The aim of this report is to examine how the operations in a typical DC on the Swedish electricity distribution network will look like in five to ten years.

This thesis is   focused on identifying and documenting all   electrical equipment, such as devices, power lines / cables, and connectors in the facility and also on presenting a brief   technical description and information of the systems around the reactors.   Furthermore there will be a brief description of LabVIEW - which is a   graphical programming language- and which devices / elements   are programmed. For further notification, I am not   responsible for the programming of the devices in LabVIEW   which I have only used as a tool in my work. The plant   for production of biogas consists of four reactors   of which the third reactor (Lakbädden)   is connected to another reactor (UASB)   where they cooperate with each other.   The reactors are used for producing   biogas in the form of methane gas.The reactors I and II are   connected to, various electrical devices as, flow meters, temperature   sensors, frequency converter and   more.

This thesis considers the development of the software for an, newly developed, embedded real-time control system, based on a Periferal Interface Controller (PIC). The control system is developed to be used for several different applications. In this thesis work, software for two different applications are developed. The first task is a time controlled system, while the other task is implementation of aPI-/PID-controller. A user interface is also developed and implemented.The time controlled system is an automatic horse feeder, which is used for feeding horses at certain predefined points in time.

Title: Information storage - A growing problem? Authors: Göran Svanhall Pär Truedsson Erik Ponnert Tutor: Bengt Carlsson Problem: Every day companies, regardless of size, produces new information that needs to be stored. In the information society of today, the characteristics of the information changes both in size and complexity. This results in higher demands on which storage solution that suits the company and their field of business. New and more innovating storage solutions enters the market, but are they necessary to smaller companies of development active in the IT society? Questions to Answer: Is data storage a growing problem for companies of development active in the IT society? How do traditional storage solutions manage the information growth of today? How urgent is the need of a new storage solution? Which features are prioritized in the future storage solution? Method: By performing a quantitative survey we delivered an inquiry to several companies, which answers will help us answering our above mentioned questions.

This report is regarding an electrical installation of an alarm system on a post fishingboat called Andromeda. The background of the installation was an earlier andinadequate alarm system that led to a motor failure. The ship was taken out of serviceand was sold to Björn Magndahl who rebuilt it to a yacht.The project was conducted partly by developing the existing systems, partly bydocumenting the work by means of electrical blue prints. Except the alarm systems, aninstallation of the frequency control unit for the bow thruster was installed.The installation was working fine and the outcome of the documentation was handedover in a form of a binder during the test drive of the systems and the assignment wasapproved..